Mohair Velvet and Silk Velvet buyers consider this: You have just invested a considerable amount of money in a high quality silk velvet or mohair velvet. Are you really considering upholstering with it yourself. Use an experienced upholsterer who, to be brutally honest, should not need the instructions that follow.
Some velvets are woven with a nap others are not. It is not a problem either way. If there is a nap you need to know which way it goes as that affects the process of upholstering. When you run your hand down the mohair velvet or silk velvet the smoothed direction indicates the direction of the nap. Remember this, it is important.
I’m assuming that you have already checked that the fabric is not damaged and that each piece is from the same dye lot.
The nap should be upholstered downwards for:
- the back;
- the seat; and
- side surfaces.
The nap should be upholstered from the outside inwards for:
- arm rests.
How do you flip your cushions? Top to bottom or left to right?
Most people flip from top to bottom. It is therefore standard upholstering practice to upholster the front and the back the opposite way. IE when they are flipped over the nap is the same.
You should use a layer of wadding between the foam and the fabric. The wadding can be either cotton or synthetic it does not really matter but check with any fire rating requirements. Again check that you are using the right kind of foam but HR foam or cold foam are both fine.
However if the pile is vertical then we advise the additional use of a cotton slip-cover.
Going back to the foam for a minute we advise that you use white wadding. In certain circumstances it is possible that grey wadding will ‘bleed’ causing marks on your beautiful Mohair Velvet. For example this may be caused from moisture used in the cleaning process.
Always use wadding on the arm rests as a protective layer to help eliminate ‘sharp’ edges. Using wadding on arm rests will thus reduce wear and tear considerably.
For the piping never use synthetic piping cord, always use cotton piping cord. As with the arm rests this will reduce wear and tear by eliminating the ‘sharper edges’.
Again to reduce wear and tear also use the length of the fabric to make the piping. this will look better as well.
Happy Upholstering
















BS7176 BS5852 Crib 5
19 July, 2010
What is BS5867 / BS 5867 part 2 type B? type C?
Posted by KOTHEA - Passionate About Fabrics For Top Designers under Contract Fabric, Curtain Fabric | Tags: contract fabric, contract fabrics, curtain fabric, faux silk, silk fabric, silk fabrics |Leave a Comment
As an interior designer you do *NOT* need to understand the details of the test nor the performance criteria that needs to be achieved.
However interior designers are responsible for the project/installation and because this is a serious are concerning fire risk you DO NEED to:
- Be certain what standard is required for your project/installation;
- Know that you are specifying fabric that meets the appropriate standard; and
- Prove that the fabric you have installed is up to the job.
So here is what you need to do to achieve that, essentially what you need to do to do your job and to ensure you have covered the bases of your responsibility.
1. Determine the fire retardancy standards that need to be adhered to. This may involve contacting the local fire officer. Determine what documentation you need to provide them.
2. Liaise with your fabric supplier to determine if the fabric either:
- inherently meets the standards; or
- requires treatment.
3. On purchasing the fabric, specify the treatment required. You would say to the fabric company “Treat the fabric to the contract curtain standard BS 5867 part 2 type B, and provide me with documentation showing this has been done”.
4. What you have done now is to specify what standard of treatment has to be undertaken. By doing that there is no guarantee that the fabric will pass the appropriate test even though it has been treated to a standard where is should pass the test. Normally you will receive a document saying that the fabric has been treated to the standard. THIS DOES NOT MEAN IT HAS PASSED THE STANDARD. You need to determine if you want your specific batch of fabric to be specifically tested (after treatment). For larger projects this will almost certainly be prudent to undertake. You will need to purchase additional fabric prior to treatment and engage the services of a fabric testing factory (not treatment factory). At the end of that process you will receive documentation stating that the fabric meets the required standard.
Here is related information on fire retardacy for contract upholstery (Crib 5, BS7176 BS5852) and durability of fabric for contract and domestic upholstery. More…
The following test details are not normally required to be known by the designer:
Share & Enjoy!